- 1Standard Handbook of Chains for Power Tr
- 2MSS SP-55-2001 Quality Standard for Stee
- 3JIS F7002-1992 Ships-Tachometer for eng
- 4JIS C 0033-1993 Environmental testing Pa
- 5JIS C 5402-11-14-2006 Connectors for ele
- 6IEEE 1101.10-1996 IEEE Standard for Addi
- 7UL 1517-2007 Standard for Hybrid Persona
- 8UL 507-2007 Standard for Electric Fans
- 9IEEE 1725-2006 移动电话用可再充电电池标准
- 10UL 864-2007 Standard for Control Units f
battery standard for engine starting tests
- 文件大小:17.19KB
- 浏览次数:
- 发布时间:2012-11-10
本资料包含pdf文件1个,下载需要1积分
battery standard for engine starting testsThis procedure applies to wet charge” batteries only and ensures that batteries used for cold
room starting tests are properly prepared to preclude test results being influenced by varying
battery condition. The term wet charge” applies equally to standard, low maintenance and
maintenance-free types.
1.1 COMMONALITY. This is a CONTROL TEST and can be used to qualify vehicles or
components throughout the world. The test may be conducted at any location having the
necessary equipment and facilities. Proposed revisions to this procedure must be submitted per
FAP 03-179.
2.0 INSTRUMENTATION
2.1 Hydrometer.
2.2 Thermometer.
2.2 All test measurement equipment must be calibrated and maintained per FAP 03-015, Control,
Calibration, and Maintenance of Measurement and Test Equipment.
2.3 All applicable safety guidelines and procedures must be followed.
3.0 EQUIPMENT AND FACILITIES
3.1 Battery charging bench with adequate fume extraction facilities.
3.2 Battery charger incorporating digital volt meter and ammeter.
4.0 SAMPLE PREPARATION
4.1 Ensure that batteries are to the latest release level, at least two weeks old but no older than 120
days since manufacture. Record battery type, rating and date code.
4.2 Ensure that electrolyte level of each battery cell is approximately 6 mm (0.25 in) above the top
of separator or to level line. (Not applicable to maintenance free batteries.)
5.0 OPERATION
5.1 Charge batteries by one of the methods listed below. During the charging period, maintain
electrolyte temperature between 15-50°C (60 - 120°F). (NOTE: A battery is fully charged
when its on charge” terminal voltage, charging current or specific gravity remains constant
within 0.01 volts, 0.05 amp or 0.002 units respectively, for three consecutive readings taken at
one hour intervals.)
5.1.1 Charge standard or low maintenance batteries either at twice the rated conditioning current (2 to
10 amp) or at a constant 14.0 ± 0.1 volts until fully charged. (See NOTE in Step 5.1 above.)
- 1武汉市xxxxx楼施工组织设计
- 2监控《从入门到精通技术学习资料》-中鼎安防网络
- 3建筑电气识图基础-华侨大学信息学院高清版
- 4GB/T 20090.5-2012 信息技术 先进音视频编码 第5部分:参考软件
- 5石灰土压实度的控制
- 6西班牙联排别墅设计SU模型
- 7华东建筑设计院cad制图模板
- 8考虑闭环稳定性的曲柄滑块机构集成设计
- 9DB36/T 455-2005 乌索酸标准品
- 10斜瓣倾转式止回阀的研究与设计
- 11桥梁施工中混凝土裂缝产生的原因及其应对措施
- 12公路隧道通风照明设计规范
- 13种植屋面防水施工工艺_secret
- 14施工组织设计十九局遵小铁路
- 15常用建筑给水管材技术经济比较