机械类毕业设计英文文献
- 文件大小:47KB
- 浏览次数:
- 发布时间:2017-03-10
本资料包含doc文件1个,下载需要1积分
机械类毕业设计英文文献Introduciton of Machining
Have a shape as a processing method, all machining process for the production of the most commonly used and most important method. Machining process is a process generated shape, in this process, Drivers device on the workpiece material to be in the form of chip removal. Although in some occasions, the workpiece under no circumstances, the use of mobile equipment to the processing, However, the majority of the machining is not only supporting the workpiece also supporting tools and equipment to complete.
Machining know the process has two aspects. Small group of low-cost production. For casting, forging and machining pressure, every production of a specific shape of the workpiece, even a spare parts, almost have to spend the high cost of processing. Welding to rely on the shape of the structure, to a large extent, depend on effective in the form of raw materials. In general, through the use of expensive equipment and without special processing conditions, can be almost any type of raw materials, mechanical processing to convert the raw materials processed into the arbitrary shape of the structure, as long as the external dimensions large enough, it is possible. Because of a production of spare parts, even when the parts and prefer machining.
Strict precision and good surface finish, Machining the second purpose is the establishment of the high precision and surface finish possible on the basis of. Many parts, if any other means of production belonging to the large-scale production, Well Machining is a low-tolerance and can meet the requirements of small batch production. Besides, many parts on the production and processing of coarse process to improve its general shape of the surface. It is only necessary precision and choose only the surface machining. For instance, thread, in addition to mechanical processing, almost no other processing method for processing. Another example is the blacksmith pieces keyhole processing, as well as training to be conducted immediately after the mechanical completion of the processing.
Primary Cutting Parameters:
Cutting the work piece and tool based on the basic relationship between the following four elements to fully describe : the tool geometry, cutting speed, feed rate, depth and penetration of a cutting tool.
Cutting Tools must be of a suitable material to manufacture, it must be strong, tough, hard and wear-resistant. Tool geometry -- to the tip plane and cutter angle characteristics -- for each cutting process must be correct.
Cutting speed is the cutting edge of work piece surface rate, it is inches per minute to show. In order to effectively processing, and cutting speed must adapt to the level of specific parts -- with knives. Generally, the more hard work piece material, the lower the rate.
Progressive Tool to speed is cut into the work piece speed. If the work piece or tool for rotating movement, feed rate per round over the number of inches to the measurement. When the work piece or tool for reciprocating movement and feed rate on each trip through the measurement of inches. Generally, in other conditions, feed rate and cutting speed is inversely proportional to.
- 1DB11/T 1063-2014 供热系统节能运行管理技术规程
- 2电池箱6
- 3不锈钢板输送机
- 4教学楼毕业设计(结构设计,施工组织)
- 5DB64/T 133-1995 塑膜暖棚猪圈
- 6DB22/T 2136-2014 铁矿粉中全铁含量的快速测定-X射线荧光谱法
- 71吨矿车 立井多绳罐笼
- 8国泰新华钢煤斗吊装方案
- 9气动隔膜泵CAD立体图
- 10GB/T 34095-2017 信息安全技术 用于电子支付的基于近距离无线通信的移动终端安全技术要求
- 11基于柔索驱动的踝关节康复机器人的研究
- 12深圳市建设工程造价员资格考试辅导班教程
- 13主减速器轴承的静态分析与选型
- 14基于CFD的磁液悬浮式血泵优化设计
- 15安装工程质量检验评定手册