手机按键模具设计
- 文件大小:1.43MB
- 浏览次数:
- 发布时间:2017-03-10
本资料包含doc文件1个,下载需要20积分
手机按键模具设计With the rapid development of Chinas rapid economic development of Chinas mold into a new stage, a variety of injection molded plastic products and injection molding of plastic parts in the national development accounted for an irreplaceable role in moldoccupies an extremely important position in the industry, is an important part in the mold.
Phone as communications equipment life for all to see this article on the mainstream market on the button bar phone button mold design process and the specific method of analysis and specific instructions. First, the plastic parts of the material properties and structural processes were analyzed to determine the size of the phone keys. Secondly, use of the corresponding injection to be checked, and on the injection cavity distribution of pieces of a mold, forming a set of phone keys. In the design process, the design and calculation of various systems such as gating system, launched institutions, mold release, parting surface, gating, shunt, mainstream Road. Finally, drawing instructions to the various parts of the mold, and with the assembly drawing and the various parts of Figure, and to make a summary of the design
Keywords: mold plastic parts phone keys injection machine
目录
摘要...........................................................................................................................2
ABSTRACT..3
目录..4
第-章 绪论.6
第二章 塑料手机按键结构和工艺分析.................................................................8
-、塑件的分析 ..............................................................................................8
二、塑件材料的分析........................................................................................9
三、 结构工艺..................................................................................................9
(-) 塑件的精度................................................................................10
(二) 塑件的壁厚................................................................................10
(三) 塑件的表面光洁度....................................................................10
(四) 塑件圆角....................................................................................11
(五) 拔模斜度.11
四、 塑件的成型参数.....11
第三章 塑件的设计和注射剂校核.12
-、 分型面和型腔的选择和设计.12
(-)分型面的选择.12
(二) 型腔布置........13
(三)型腔尺寸的确定.15
二、 注射机的选择校核.....17
(-) 注射机的选择.17
(二) 体积的计算19
(三)注射机的校核.19
1、最大注射量校核...19
2、锁模力的校核...20
3、注射压力校核...20
4、脱模力的计算....21
- 1SR2020-03-00反应釜
- 2现代住宅楼建筑施工图
- 3齿轮机构/力的分解SolidWorks设计
- 4某机动雷达面阵天线自动架撤联动机构的设计
- 5QB/T 1858-1993 香水、花露水
- 6沪建安质监通【2014】5号关于2014年第一季度全市住宅工程质量专项检查情况的通报
- 7东陈加压泵站全套设计图
- 8iPhone手机SolidWorks设计
- 9自动排片机总装图
- 10(新7)室内采暖系统安装质量分户验收记录表
- 11手架在现浇桥梁施工中的计算及应用
- 12excel表格_插值计算器
- 1320162_施工管理资料全套施工管理资料表格Excel版600多份表格.part01
- 14GB/T 20127.13-2006 钢铁及合金 痕量元素的测定 第13部分 碘化萃取-苯基荧光酮光度法测定锡含量
- 15压力容器分气包射线检测新方式