机械设计题目:带式运输机传动系统中的展开式二级圆柱齿轮减速器
- 文件大小:22.81KB
- 浏览次数:
- 发布时间:2013-01-18
本资料包含doc文件1个,下载需要20积分
机械设计题目:带式运输机传动系统中的展开式二级圆柱齿轮减速器齿轮箱作为一种基础设备,被广泛应用,其性能优劣直接影响着机械设备的运行状况。而目前许多工厂尚不具备制造高精度齿轮箱的加工设备。另一方面,再好的设备加工出的零件也存在误差,其累积误差仍会影响齿轮箱装配后的传动性能。本文提出的无侧隙传动技术,从新的角度提出了在设备条件不足的情况下,利用主副齿轮来实现飞剪机的无侧隙传动。“零侧间隙啮合”是:在尽量周到地考虑飞剪机工作条件下,将齿轮加工成在某一特定状态(例如温度,轴承游隙等)为“零侧间隙啮合”,事实上并非没有侧隙,只能说齿轮啮合的齿侧间隙是很小的。常消除齿隙有很多方法,如提高加工精度,利用圆锥齿轮,四个齿轮串联布置机构,利用主副齿轮。本设计就是采用主副齿轮。在某些飞剪机上,为了改善上下滚筒同步齿轮的工作性能,被动轴上的齿轮往往采用主副齿轮结构,以便齿轮在无侧隙情况下工作,减少和消除冲击负荷。利用主副齿轮则能有效消除齿侧间隙,并且在减速器突然制动时,仍然能实现无间隙传动。关键词: 飞剪机;减速器;间隙;主副齿轮AbstractReducer is widely used as a basic facility. It’s performance which is excellent or inferior has an impact on the running state of the mechanical equipment. But many factories don’t have machining equipment for manufacturing high-precision reducer at present . On the other hand, even though the part is manufactured by the best equipment, it also has error. And their accumulative errors still affect on the transmission performance of reducer after assembled.No lateral gap technology in this article put forward using main-second gear to achieve no lateral gap transmission of the flying shears at the state of having no adequate equipment by a new way. “No lateral gap ingear” is processing gear to a particular state(such as temperature, bearing clearance, etc.),considering the working conditions as much as possible. But in fact,it’s impossible that the gears have no lateral gap.The laterl gap of the gear is very small. Usually there are many ways to eliminate lateral gap,such as improving the processing accuracy,using bevel gear, using four tandem gears and using main-second gear.This design has used the main-second gear. In some flying shears the running performance of the top and bottom selsyn roller usually can be improved by using main-second gear on the gear of the driven shaft.It can make the gear working at no lateral gap and eliminate shock load. The use of the main-second gear can eliminate lateral gap,and it still can achieve no lateral gap transmission when the reducer is suddenly braked.Key words:Flying shears; Reducer; Lateral gap; Main-second gear 目 录1 前言 12 研究内容 23 传动方案的分析与拟定 24 电动机的选择 2
- 1万向节设计
- 2HG/T 4268-2011 纺织染整助剂 棉用固色剂 固色效果的测定
- 3建筑工程抗震设防分类标准GB 50223-2008
- 4GB/T 29265.1-2017 信息技术 信息设备资源共享协同服务 第1部分:系统结构与参考模型
- 5混凝土实验资料
- 6GB/T 6131.4-2006 铣刀直柄 螺纹柄的型式和尺寸
- 7YD/T 2265-2011 IPTV管理体系结构
- 8水工砼钢筋施工规范
- 9DB41/T 1643.3-2018 电梯运行监测系统技术规范 第3部分:现场采集装置技术要求
- 10CM6132型精密车床主传动系统数控改造设计
- 11公园规划设计总平面图
- 12教堂的拼图SolidWorks设计
- 13南湖大桥全套图纸
- 14钻孔灌注桩常见工程事故预防措施
- 15挂篮施工作业指导书封面